High frequency board usually use FR4 glass fiber lamination, but also the whole of the epoxy glass cloth repression, more uniform color the entire pcb board, bright. Density larger than the low frequency pcb board
High-frequency electronic devices is the development trend, especially in the growing wireless networks, satellite communications, and information products to high speed and high-frequency, and voice communications products to large capacity and fast transmission of wireless, video, and data normalization.
Therefore, the development of next-generation products require high frequency board, satellite systems, mobile phone base stations and other communications products received must be applied to high-frequency circuit boards, and the inevitable rapid development in the coming years, will be a large demand for high-frequency board.
(1) The dielectric constant (Dk) must be small and very stable, usually the smaller the better signal transfer rate
(2) The dielectric loss (Df) must be small, which mainly affects the quality of signal transmission, the smaller dielectric loss the smaller signal loss
(3) Consistent with the thermal expansion coefficient of copper
(4) Low water absorption, high water absorption will affect the dielectric constant and dielectric loss at the time of moisture.
(5) Other heat resistance, chemical resistance, impact strength, peel strength, etc. must also be good.
Q:How to get a PCB prototype quotation?
A:1.PCB Gerber file
2.PCB technics requirements(board thickness, copper thickness, solder mask color, surface treatment)
Q:Is your tooling cost one-off payment?
Payment & Shipping Terms:
|Color:||Green||Min Line Space:||4mil|
|Min Line Width:||4mil||Copper Thickness:||1OZ|
FR4 High TG PCB Board Multilayer PCB EMS Electronic Metal Detector PCB Board
|Origin:China||Special: FR4 Material|
FR - 4 epoxy glass fiber cloth substrate, based on epoxy resin as binder, with electronic level glass fiber cloth as reinforcing material of substrate. Its bonding sheet and thin copper-clad r.p. panel and inner core is an important base material in production of multilayer printed circuit board,This kind of product is mainly used for double-sided PCB, dosage is very large. Epoxy glass fiber cloth substrate, the most widely used model for FR - 4, in recent years because of the electronic product installation technology and PCB technology development needs, appeared high Tg FR - 4 products.
The mechanical properties of epoxy glass fiber cloth substrate, size stability, impact resistance, moisture resistant to higher than paper substrate. Its excellent electrical performance, high working temperature, itself performance affected by environment. On the processing technology, than other resin fiberglass cloth substrate has great superiority
Radio frequency (RF) and microwave PCB’s are a type of PCB designed to operate on signals in the megahertz to gigahertz frequency ranges (medium frequency to extremely high frequency). These frequency ranges are used for communication signals in everything from cellphones to military radars. The materials used to construct these PCB’s are advanced composites with very specific characteristics for dielectric constant (Er), loss tangent, and CTE (co-efficient of thermal expansion).
High frequency circuit materials with a low stable Er and loss tangent allow for high speed signals to travel through the PCB with less impedance than standard FR-4 PCB materials. These materials can be mixed in the same Stack-Up for optimal performance and economics.
|1||Layer:||1 to 24 layers|
|2||Material type:||FR-4, CEM-1, CEM-3, High TG, FR4 Halogen Free, Rogers|
|3||Board thickness:||0.20mm to 3.4mm|
|4||Copper thickness:||0.5 OZ to 4 OZ|
|5||Copper thickness in hole:||>25.0 um (>1mil)|
|6||Max. Board Size:||(580mm×1200mm)|
|7||Min. Drilled Hole Size:||4mil(0.1mm)|
|8||Min. Line Width:||3mil (0.075mm)|
|9||Min. Line Spacing:||3mil (0.075mm)|
|10||Surface finishing:||HASL / HASL lead free, HAL, Chemical tin, Chemical Gold, Immersion Silver/Gold, OSP, Gold plating|
|11||Solder Mask Color:||Green/Yellow/Black/White/Red/Blue|
|13||Hole tolerance:||PTH: ±0.076 NPTH: ±0.05|
|14||Package:||Inner packing: Vacuum packing / Plastic bag,Outer packing: Standard carton packing|
|16||Special requirements:||Buried and blind vias+controlled impedance +BGA|
|17||Profiling:||Punching, Routing, V-CUT, Beveling|
Packaging Details: Anti-static, vacuum packing,corrugated export carton,bubble
Delivery Detail: 3-5 working days after we receive customers' payment
Payment Method:T/T ,Paypal ,West Union
1. What kind of PCB file format I need to submit for the production?
A. Gerber files and BOM
2.Can you produce it for me,if we dont have the PCB file/Gbr file, only a sample?
A. Send us the sample, and we will work out the gerber files and clone the pcb for you.
3.Which countries have you worked with?.
A: We have built cooperation with customers from all over the world, mostly America and Europe
4. Are my PCB files safe when I submit them to you for manufacturing?
A:We respect customer's copyright and will never share these files with any other 3rd parties without your permission.